Various
Command Air System
Requires the following components
CONTROL BOX #: CIMC-213-01-03-01
KEYPAD #: CIDU-252-01-06-13
KEYPAD CABLE #: CCBL-168
MULTI-COLORED LIGHT #: CICL-239-01-01-01
LIGHT CABLE #: CCBL-170
Optional Components
TRIM RING #: CRING-xx
EXTENDED LIGHT CABLE #: CCBL-176
“Y” LIGHT CABLE #: CCBL-233
The Command Air System controls a Multi-Speed Blower and Colored LED light(s). The user interface is four-buttons with an LED light over each button.
Requires the following components
CONTROL BOX #: CIMC-213-01-03-01
KEYPAD #: CIDU-252-01-06-13
KEYPAD CABLE #: CCBL-168
MULTI-COLORED LIGHT #: CICL-239-01-01-01
LIGHT CABLE #: CCBL-170
Optional Components
TRIM RING #: CRING-xx
EXTENDED LIGHT CABLE #: CCBL-176
“Y” LIGHT CABLE #: CCBL-233
System Functions
Upon power up of the system without user intervention, the display will enter the standby mode of the configuration previously set. In standby mode:
♦ The user can operate the blower. The LED above the “Jets” icon will light dimly to indicate that the blower is operable.
♦ The user can operate the color LED light(s). The LED above the “Light” icon will light dimly to indicate that the light(s) is operable.
TIMERS
Pressing and releasing the “Jets” icon button will turn on the blower at high speed and start a 20-minute run timer. Pressing and releasing the “Jets” icon button a second time during the 20-minute run time will turn off the blower and cancel the timer. If the 20-minute run time expires, the blower and light(s) will turn off. If the blower is shut down by the user before the 20-minute timer expires, the light(s) will continue operating.
BLOWER CONTROL
When the “Jets” icon button is active (indicated by a dimly lit “Jets” LED) pressing and releasing the button will turn on the blower and start a 20-minute run timer. The operating blower will be indicated by a full-bright LED. Pressing and releasing the button a second time during the 20 minute run time will turn off the blower and cancel the timer. While the blower is operating, pressing and holding the “Jets” icon button for two seconds will activate the “+” and “-“ buttons, indicated by the LEDs over the “+” and “-“ buttons illuminating full-bright. Pressing either “+” or “-“ button will increase or decrease the speed of the blower. Pressing the “-“ button for two seconds at the lowest speed will cause the blower to enter the wave mode. When in the wave mode, the blower will slowly cycle between high and low speeds. Pressing either “+” or “-“ button will exit the wave mode at the current blower speed setting. The “+” and “-“ buttons will remain active (lit) for ten seconds without input, and then extinguish.
LIGHT CONTROL
Pressing and releasing the “Light” icon button will start the colored LED light(s) in color changing mode. When the light(s) are functioning, the LEDs over the “Light” icon button will illuminate full-bright. While the light(s) are functioning, pressing and holding the “Light” icon button for two seconds will activate the “+” and “-“ buttons, indicated by the LEDs over the “+” and “-“ buttons illuminating full-bright. Pressing either “+” or “-“ button will
change the light(s) from color changing mode to color hold mode in the color present when the button was pressed. Subsequent pressings of the “+” or “–“ button will step the color forward or backward in the color sequence. Pressing both “+” and “–“ buttons simultaneously will return the light(s) to the color changing mode. The “+” and “-“ buttons will remain active (lit) for ten seconds without input, and then extinguish. Pressing and releasing the “Light” icon button will turn the light(s) off and the LED over the “Light” icon button will return to dimly lit, and
the LEDs over the “+” and “-“ buttons will turn off. The light(s) will come back on in the color displayed when it was turned off.
DRY CYCLE
20 minutes after the blower has been idle; the blower will turn on for 1 minute to dry the air lines and air jets. The blower will start at low speed for about 6 seconds, ramp to high speed over about 5 seconds and remain at high speed for the duration of the cycle. During the dry cycle, the LED over the “Jets” icon will blink. Pressing the “Jets” icon button during the dry cycle will stop the dry cycle.